220 in 1 dump
Moderator: Moderators
220 in 1 dump
I have purchased the Kazzo cartridge "INL Retro" Dumper-Programmer, and It seems to not working on my computer using the Anago wx software. However I have a problem dumping a copy of "220 in 1" Do anyone have some tips for how to do it? i have tryed every script and it didnt work. can anyone help my?
- krzysiobal
- Posts: 1037
- Joined: Sun Jun 12, 2011 12:06 pm
- Location: Poland
- Contact:
Re: 220 in 1 dump
Please provide good quality photos of PCB of your cartridge from both sides, there are no fortune-tellers.
- krzysiobal
- Posts: 1037
- Joined: Sun Jun 12, 2011 12:06 pm
- Location: Poland
- Contact:
Re: 220 in 1 dump
After briefly analyzing the PCB I would assume:
so please write proper script for that.
* There is CHR-RAM but it is write-protected in some modes
* Does the cartridge contains UNROM Games (Contra?)
* There is reset detection circuitry so it need to be bypassed for the dumping (shorting or opening capacitor, depending on the connection which I don't see casue of bad light at bottom-right corner of top layer of cartridge - near the diode)
Code: Select all
I would assume
[vmPPPPPPp] register ($8000-$ffff ?)
|||||||||
||+++++++- 16K/32K PRG bank (p ignored in 16k mode)
|+-------- mirroring (no idea if 0=V or 0=H)
+--------- PRG mode (no idea if 0=16K or 0=32k)
* There is CHR-RAM but it is write-protected in some modes
* Does the cartridge contains UNROM Games (Contra?)
* There is reset detection circuitry so it need to be bypassed for the dumping (shorting or opening capacitor, depending on the connection which I don't see casue of bad light at bottom-right corner of top layer of cartridge - near the diode)
- krzysiobal
- Posts: 1037
- Joined: Sun Jun 12, 2011 12:06 pm
- Location: Poland
- Contact:
Re: 220 in 1 dump
So finally I think it is:
In order to dump it, you need to
1) Short the capacitor
2) try this script (warning - I don't see in FCEUx source any mapper number that follows this description, so probably new mapper need to be assigned & emulator modified)
Code: Select all
$8001 $8000 (mask: $8001)
[......wP] [PmvPPPPp]
|| ||||||||
|+----+||+++++- 16K/32K PRG bank (p ignored in 32k mode)
| |+------- PRG mode (0=32K,1=16K)
| +-------- mirroring (0=V,1=H)
+--------------- 1=CHR-RAM is write protected
On power up & reset, both registers are cleared
1) Short the capacitor
2) try this script (warning - I don't see in FCEUx source any mapper number that follows this description, so probably new mapper need to be assigned & emulator modified)
Code: Select all
board <- {
mappernum = 255,
cpu_rom = { size_base = 2097152, size_max = 2097152, banksize = 0x4000 },
ppu_rom = { size_base = 0, size_max = 0, banksize = 0 },
ppu_ramfind = false, vram_mirrorfind = false
};
function cpu_dump(d, pagesize, banksize) {
for (local i = 0; i < pagesize; ++i) {
cpu_write(d, 0x8000, (i & 0x1F) | (1 << 5) | ((((i >> 5) & 1) << 7)));
cpu_write(d, 0x8001, (i >> 6) & 1);
cpu_read(d, 0x8000, banksize);
}
}
Last edited by krzysiobal on Sun Nov 11, 2018 11:57 am, edited 1 time in total.
Re: 220 in 1 dump
It didnt work it say reader open error
And i have the capacitor shorting
And i have the capacitor shorting
- krzysiobal
- Posts: 1037
- Joined: Sun Jun 12, 2011 12:06 pm
- Location: Poland
- Contact:
Re: 220 in 1 dump
I am not familiar with kazzo errors but maybe try the updated script above.
BTW. Does the cartridge with shorted capacitor works in console?
BTW. Does the cartridge with shorted capacitor works in console?
Re: 220 in 1 dump
That means anago is unable to communicate with the kazzo. Here are a few common cases: it is not connected properly, it is not set in the correct mode, it was not flashed with the original kazzo firmware or the software setup was not completed.roytje13 wrote:It didnt work it say reader open error
I'm assuming the drivers were not properly installed. You should attempt to follow INL guide again and making sure you do every step and that they are successful.
Also you might want to make sure you can dump some random generic game, like Super Mario Bros. (as NROM) before attempting anything else.
Re: 220 in 1 dump
MLX does it work on windows 10 64x
Re: 220 in 1 dump
It should? I tested it on Windows 7 and Windows 8.1 it worked like a charm. I'm pretty sure you haven't properly installed the associated software/drivers.
Re: 220 in 1 dump
i have super mario bros 3 (pal)
i reinstaled the drivers and it didnt work
wat should i do?
i reinstaled the drivers and it didnt work
wat should i do?
Re: 220 in 1 dump
Try another computer? Does your kazzo has a switch? Which position is it in?
Re: 220 in 1 dump
its on run pos.
i have an other pc with win 98
i have an other pc with win 98
Re: 220 in 1 dump
I can try to run it on vurtual windows xp